LEDO Blog for LED Car Light

Have you ever been blinded by someone else’s headlights, or noticed that your own headlights are not illuminating the road directly in front of you? If all you can see is the foliage on the side of the road, or oncoming drivers are constantly flashing their high beams or honking their horn at you, most likely your headlights are misaligned and giving those other drivers an eyeful. They're easy to adjust with a few measurements and a screwdriver. As the automotive lighting manufacturer in China , we are going to tell you how to adjust headlights for the perfect aim step by step. 1, Level your car. Start by removing any excess weight from the trunk of the car. Also, ensure that the tire pressure in all tires is at the manufacturer's recommended levels. If possible, have somebody sit in the driver's seat, and that the gas tank is half-full. As well as this, check that your headlight aim adjustment wheel (if fitted) is at the zero position. 2, Position your car.

The installation of the light on a 2013 Subaru Outback on the left side is Okay but on the right side for the main headlight(low beam) is next to impossible with out removing the whole headlight from the vehicle with in addition requires removing the bumper. I took my caravan for a short drive after installation. They look awesome when you look at the car. Crisp, white with a bluish tinge.. They're pretty bright, when you compare them to the stock halogens against a wall right in front of the car, led headlight looks stronger, as you can see in the picture. when driving around, the light beam just seems weak a little. Later I found that it is not because lighting is being weaker... the problem is that anything over 6000K-7000K in color will lack "darkness piercing" ability, meaning they really don't light up the road very usefully. For the best penetration in the darkness, you want between 4000k-5000k (there'll be people that argue that sunlight is 5300k

I have a 2005 GMC envoy. This LED headlight bulbs look very nice in them. I love how easy it was to put in, which only took 5 minutes for each bulb. I will share more pictures of what they look like at night. 6000k is the perfect color temperature, not too blue and it looks like daytime. They are bright and as far as i can tell, the leds are positioned just right for the reflector just like halogens which is good. 2 year warranty from Ledoauto, I’ m confident in knowing will be using these for a while. Know more information from the automotive led lights wholesale website

Purchased these 194 led bulbs to replace dome light and backup reverse light in my 2008 Infinite G37. The fit was perfect, the level of illumination is great, brighter a little than stock halogen bulbs. Bulbs are pure white, doesn’t tend to blue or yellow. LEDs are diodes, one led bulb has only 1.5W while T10 halogen bulb has 6-8W, LED bulbs are more energy efficient. 360 degree light angle like halogen bulbs, don’t need to worry about blind angle problem. If you want a low cost solution to get you into LED's without a huge investment, then these will do the job, but don't expect to read with them on. Upgraded with pictures! 

Automotive LED light bulbs are high intensity and attractive, but they will has hyper flash problem if used on automotive turn signal light. I have been constantly searching for a set of yellow led lights that did not activate the hyper flash without having to place a resistor. These 2835 SMD LED bulbs are very nice. They looks not special. While I put these in my 2014 Honda Accord for the rear turn signal light, they work great without error on OBC and are so bright. They fit nice and secure to the factory connector and fit perfect in the housing. Matches the existing yellow  LED's that are there for the brake lights and the normal rear red lights for nighttime visual. I would recommend these lights as they are really convenient on installation. Besides, they are 6W per bulb only while the stock halogen bulbs are 21W, I think this one really can save power for me.

China is a magical place, we can find many interesting and new developed products here with wonderful design. Today I’d like to recommend you this 3D design T10/ 194 LED bulb . We all know T10 LED lighting are widely applied to cars as interior light and number plate light. Users should concern on installation and lighting, plug and play is important, soft and bright lighting is necessary too. These 3D design T10 LED bulbs use Osram LED chip with PC cover on it, lighting is bright but soft, it isn’t like other T10 bulbs which have LED on surface directly, that lighting is glaring and eye can’t look directly. I installed these on my 2012 Volkswagen Passat- what a major upgrade! Looks amazing, the bulb is rated at 6000K, color is very white and crisp. I took literally 30-45 seconds to install each one, no load resistors needed. I feel like these are a great deal for the price, nearly 1.9$ per pcs only. They are listed as street-legal for car as in